What will happen if earth looses it's Gravitation force

-
If the Earth were to suddenly lose its gravitational force, the consequences would be catastrophic.

First and foremost, all objects on the surface of the Earth would be sent hurtling into space. This includes everything from buildings and vehicles to plants and animals. The atmosphere would also be pushed out into space, causing a complete loss of air and rendering the planet uninhabitable.

In addition, the loss of gravity would have a major impact on the rest of the solar system. Without the gravitational pull of the Earth, the Moon would be sent hurtling away and the orbits of other planets would be altered. This could potentially lead to collisions and other catastrophic events throughout the solar system.

It's worth noting that the loss of gravity on Earth is a highly unlikely event. The gravitational force on Earth is created by the mass of the planet and it's not something that can be easily turned off or removed. However, if by any chance it happens, it would mean the end of life as we know it on our planet.

In summary, the loss of gravity on Earth would be a catastrophic event with dire consequences for all life on the planet and potentially for the entire solar system.

Comments

Post a Comment

Its not necessary everyone should know everything feel free to ask or tell :)

Popular posts from this blog

Estimation of total chlorophyll by Aron's method

-
Purpose:- Estimation of total chlorophyll by Arnon's method. Requirement:- Spectrophotometer Buchner's funnel, filter paper test tube, Fresh leaves. measuring cylinder pestle & mortar 80% Acetone  Formula:- 20.2 (A645) +802 A663) / 1000 x W Principle:- Chlorophyll is extracted in 80% acetone & the absorption at 660 nm& 645 nm are read in s spectrophotometer using the absorption co-efficient, the amount of chlorophyll is calculated Procedure:- 1) Weigh 1 gm of finely cut & well mixed representative sample of a leaf or fruit tissue into a clean mortar 2) Grind the tissue to a fine pulp with the addition of 20mil of 80% acetone   3) Centrifuge (5000 rpm for 5 min) & transfer the supernatant to a 100 ml volumetric flask  4) Repeat this procedure until the residue is colorless wash the mortar and pestle  thoroughly with 80% acetone and collect the clear washing in the volumetric flask 5) Make up the volume to 100 ml with 80% acetone  6) ...
Read more

Determination of Stefan's constant

-
Image
Aim:-  To determine the value of Stefan's constant. Apparatus:-  Black body radiation unit, Ammeter, Voltmeter, connecting wires, DC source. Theory:-  Stefan's constant: A physical constant denoted by  σ , is the constant of proportionality in the Stefan's-Boltzmann law- the total intensity radiated over all wavelength increases as the temperature increases Procedure:- 1) The electrical connections are made as shown in the circuit diagram. 2) Copper black body radiator is preheated to  30 0 C   by setting maximum voltage in the power supply 3)after the temperature indicator indicates a temperature of about    30 0 C , the voltage is reduced to some value  4) increase the voltage in steps of 0.2 V and note down the current, hence calculate power l. 5) Determine the value of Stefan's constan t. Observations:-  Room temperature t o =t+273=......of 2) surface area of the black body  A=4π r 2  = .........m square Calculati...
Read more

Pre-Emphasis & De-Emphasis Networks

-
Image
Aim:-  To draw the frequency response of Pre-emphasis & De-emphasis networks. Introduction:- Educational trainer a useful kit for the demonstration of Pre-emphasis & De-emphasis at different time constants & plot the graph of the frequency response of Pre-emphasis and De-emphasis networks. The kit consists of 200 Hz-20 kHz audio oscillator 70µ sec & 50µ sec De-emphasis networks.  Pre-Emphasis Circuit Diagram:- DE-Emphasis Circuit Diagram:- Theory:- Pre-emphasis refers to boosting the relative amplitudes of the modulating voltage for higher audio frequencies from 2 to approximately 15 kHz . De-emphasis means attenuating those frequencies by the amount by which they are boosted.  However, Pre-emphasis is done at the transmitter and De-emphasis is done in the receiver. The purpose is to improve the signal-to-noise ratio for FM reception. A time constant of 75µ sec is specified in the RC or L/Z network for Pre-emphasis and De-emphasis. Tabular colu...
Read more